Differences

This shows you the differences between two versions of the page.

--- realraum:minielectronicsworkstationmanual [2019-02-03 17:49] – xro
+++ realraum:minielectronicsworkstationmanual [2025-11-09 09:25] (current) – external edit 127.0.0.1
@@ Line 1: / Line 1: @@
 ===== Manual for LoTHR Electronics Station ====
+Aka: Mini-TESLA
+{{:realraum:qr_lothr_etech_manualwiki.png?direct&180|}}
+ShortURL: http://shorturl.at/efoAE
+**Main-Power-Switch for everything**: located at back of box.
 ==== The Electric Load XY-FZ35 ====
@@ Line 93: / Line 99: @@
-==== The Power Supply DS30V05A ====
+==== The Power Supply RD-Tech DS30V05A ====
   * Current-Limit, setable in 0.001A increments
@@ Line 99: / Line 105: @@
   * max 5A (but current power supply limits to 72W. Need more? Go to TESLA)
   * max 26V (would be max 30V but is Buck-Converter and poewr supply only supplies 29V. Need more? Go to TESLA)
-{{:realraum:dp30v5a_htb16b51jfxxxxb1xxxxq6xxfxxx7.jpg?direct&450 |}}
-{{:realraum:dp30v5a_htb1maynjfxxxxc9xpxxq6xxfxxxl.jpg?direct&450 |}}
 === Usage ===
 See Manual stuffed into the back.
+{{ :realraum:dp30v5a_htb16b51jfxxxxb1xxxxq6xxfxxx7.jpg?direct&700 |}}
+{{ :realraum:dp30v5a_htb1maynjfxxxxc9xpxxq6xxfxxxl.jpg?direct&700 |}}
 ^ Buttons ^^
@@ Line 123: / Line 129: @@
 [[http://www.quickochina.com/uploads/USERmanual-en.pdf|Link to english Manual]]
-^Button ^ Use ^
-|CW | Lower value / Boostmode |
-|CCW | Increase Value / Standby |
-|Press | Select |
-|Long Press | Menu or exit menu|
-| CW while pressing | change TIP temperature profile |
-| CCW while pressing | calibrate Tip (only on newer firmware version) |
 If the station detects movement/temperature fluctuations of the tip, it will automatically exit standby mode.
-=== On / Off ===
+=== Usage ===
-Just turn knob CW.
+^ Mode ^ How to get there ^
+| Hard-Off | Use power-switch right of device |
+| On | Enable power-switch on the right and turn knob CW until on |
+| Boost-Mode (+ ~60°C for ~5min) | Turn knob CW until device enters boost mode |
+| Standby (~120°C) | Turn know CCW until device is in standby mode |
+| Sleep (Soft-Off) | Turn knob CCW until sleep mode is selected |
+| Set Temperature | Press knob once |
+| Menu/Settings | Hold knob down |
+| Change Tip Preset | Hold knob down while turning knob CW|
 === Set Temperature ===
-Press knob once and set temperature by turning knob.
+  - Press knob once
+  - set temperature by turning knob.
 === Change Soldering Tip ===
-Press knob and turn CW. Then select tip and confirm with button press.
+  - Hold knob down while turning knob CW
+  - Then select tip and confirm with button press.
-=== Boos Mode ===
-Turn know CW.
-=== Standby ===
-Turn know CCW.
 === Calibration ===
 Get Solder-iron-tip temperature meter from TESTLA and go to menu and select calibration.