Differences

This shows you the differences between two versions of the page.

--- realraum:minielectronicsworkstationmanual [2019-02-03 13:48] – xro
+++ realraum:minielectronicsworkstationmanual [2025-11-09 09:25] (current) – external edit 127.0.0.1
@@ Line 1: / Line 1: @@
 ===== Manual for LoTHR Electronics Station ====
+Aka: Mini-TESLA
+{{:realraum:qr_lothr_etech_manualwiki.png?direct&180|}}
+ShortURL: http://shorturl.at/efoAE
+**Main-Power-Switch for everything**: located at back of box.
 ==== The Electric Load XY-FZ35 ====
@@ Line 17: / Line 23: @@
 === Settings ===
+ {{ :realraum:htb13kozxpduk1rjsszdq6xglpxay.jpg?direct&400|}}
 ^ Protection Settings °°
@@ Line 24: / Line 32: @@
 | OTP | over-temperature protection (at > 80°C, LCD flickers) |
 | LVP | undervoltage protection (default 1.5V) \\ When discharging a battery, set this to prevent damage to the battery |
- {{ :realraum:htb13kozxpduk1rjsszdq6xglpxay.jpg?direct&400|}}
 The electronic load automatically saves the switching state before shutting down and resumes with the last state (power == on/off)
 Discharge capacity Statistics:
@@ Line 96: / Line 99: @@
+==== The Power Supply RD-Tech DS30V05A ====
-==== The Power Supply DS30V05A ====
+  * Current-Limit, setable in 0.001A increments
+  * Voltage-Lmit, setable in 0.01V increments
+  * max 5A (but current power supply limits to 72W. Need more? Go to TESLA)
+  * max 26V (would be max 30V but is Buck-Converter and poewr supply only supplies 29V. Need more? Go to TESLA)
-==== The KSGEr solering station ====
+=== Usage ===
+See Manual stuffed into the back.
+{{ :realraum:dp30v5a_htb16b51jfxxxxb1xxxxq6xxfxxx7.jpg?direct&700 |}}
+{{ :realraum:dp30v5a_htb1maynjfxxxxc9xpxxq6xxfxxxl.jpg?direct&700 |}}
+^ Buttons ^^
+| Set (short press) | Begin or Confirm/End setting current/voltage limit) |
+| EncoderKnob Press | Go to next Digit |
+| EncoderKnob CW | increase digit |
+| EncoderKnob CCW | decrease digit |
+| Set (long press) | open additional settings screen \\ program memory locations |
+| M1               | recall stored settings from memory location 1 |
+| M2               | recall stored settings from memory location 2 |
+==== T12 solering station (KSGER, Quicko) ====
 Software Version: 2.09
@@ Line 105: / Line 128: @@
 Hardware Version: ....
-=== On / Off ===
+[[http://www.quickochina.com/uploads/USERmanual-en.pdf|Link to english Manual]]
+If the station detects movement/temperature fluctuations of the tip, it will automatically exit standby mode.
+=== Usage ===
+^ Mode ^ How to get there ^
+| Hard-Off | Use power-switch right of device |
+| On | Enable power-switch on the right and turn knob CW until on |
+| Boost-Mode (+ ~60°C for ~5min) | Turn knob CW until device enters boost mode |
+| Standby (~120°C) | Turn know CCW until device is in standby mode |
+| Sleep (Soft-Off) | Turn knob CCW until sleep mode is selected |
+| Set Temperature | Press knob once |
+| Menu/Settings | Hold knob down |
+| Change Tip Preset | Hold knob down while turning knob CW|
 === Set Temperature ===
+  - Press knob once
+  - set temperature by turning knob.
 === Change Soldering Tip ===
-=== Boos Mode ===
+  - Hold knob down while turning knob CW
+  - Then select tip and confirm with button press.
 === Calibration ===
+Get Solder-iron-tip temperature meter from TESTLA and go to menu and select calibration.