3dprinting:lulzbot

Differences

This shows you the differences between two versions of the page.

Link to this comparison view

Both sides previous revision Previous revision
Next revision		 Previous revision
3dprinting:lulzbot [2018-07-13 23:55] – [Materials] xro3dprinting:lulzbot [2025-11-09 09:25] (current) – external edit 127.0.0.1
Line 20: Line 20:
   - Is the filmanet entangled? –> disentangle.   - Is the filmanet entangled? –> disentangle.
   - Load correct material profile in Cura.   - Load correct material profile in Cura.
-      * If in doubt use "Fast" –> see [[#materials|Materials]]+      * If in doubt use "Fast" –> see [[materials|Materials]]
   - Are you printing Nylon?   - Are you printing Nylon?
       * Prep with Glue Stick. Clean/Remove with Water afterwards.       * Prep with Glue Stick. Clean/Remove with Water afterwards.
Line 43: Line 43:
  
 ====== Tipps and Caveats ====== ====== Tipps and Caveats ======
 +
 +Jemand hat Ocotoprint installiert und den Lulzbot unter http://3d-lulzbot.realraum.at/ erreichbar gemacht.
  
 [[https://forum.lulzbot.com/viewtopic.php?t=1709|Guide to Obtaining Great Prints]] [[https://forum.lulzbot.com/viewtopic.php?t=1709|Guide to Obtaining Great Prints]]
Line 113: Line 115:
 Current Nozzle Size is 0.5 (self-drilled). It's fast and accurate. Don't change it if in doubt. Current Nozzle Size is 0.5 (self-drilled). It's fast and accurate. Don't change it if in doubt.
  
-We also have a 0.35 Nozzle. You will only need it for very fine prints.+<del>We also have a 0.35 Nozzle. You will only need it for very fine prints.</del>
  
 **Warning**  beware of youtube videos that show nozzle change at room temperature. read [[https://www.lulzbot.com/content/taz-user-manual-updates-and-errata|Lulzbot Errata]] **Warning**  beware of youtube videos that show nozzle change at room temperature. read [[https://www.lulzbot.com/content/taz-user-manual-updates-and-errata|Lulzbot Errata]]
Line 133: Line 135:
 ====== Materials ====== ====== Materials ======
  
-<WRAP noprint><html><div style="float:right;margin-left:1ex;margin-bottom:1ex;text-align:center;"></html> {{  :3dprinting:taz4_printing_nylon.jpg?direct&400}} \\ **Nylon Printing and Cleaning**<html></div></html></WRAP> +<WRAP center round tip 60%> ** Correct profiles for each material can be found in: **  ''~/lulzbot/cura profiles for TAZ4/'' on Würfel or  [[https://github.com/realraum/3dprinting | on Github]]
- +
-<WRAP center round tip 60%> ** Correct profiles for each material can be found in: **  ''~/lulzbot/cura profiles/''+
  
 **Fast Profile**  is alsmost always the right choice, unless you intend to print small models with very fine structures. **Fast Profile**  is alsmost always the right choice, unless you intend to print small models with very fine structures.
Line 152: Line 152:
  
 See [[materials|list of materials in realraum]] See [[materials|list of materials in realraum]]
 +
 +==== Printing with nGen ====
 +
 +no special knowledge or care required
 +
 +==== Printing with HIPS/PLA/ABS ====
 +
 +Hips, PLA and ABS like to warp to various degrees during the print due to cooling/heating expansion. Keep print at uniform temperature. i.e. encase printer.
  
 ==== Printing with Nylon ==== ==== Printing with Nylon ====
 +
 +<WRAP noprint> {{  :3dprinting:taz4_printing_nylon.jpg?direct&400}} \\ **Nylon Printing and Cleaning**</WRAP>
  
 Nylon does not stick to the print-bed. Not even with the heat turned on. Nylon does not stick to the print-bed. Not even with the heat turned on.
Line 171: Line 181:
 When the print is finished, wait for the pad cools and then VERY carefully try not to damage the print surface! When the print is finished, wait for the pad cools and then VERY carefully try not to damage the print surface!
  
-=== what can be printed ? ===+==== what materials can be printed ? ====
  
-Everything with a filament diameter of 3mm (no less and no more) and extrusion temperature below 238°C that does not clog 0.35mm nozzles, like wood-,stainless-steel-,conducitve,"magnetic"-filament does.+Everything with a filament diameter of 2.85mm-3mm (no less and no more) and extrusion temperature below 238°C that does not clog the nozzle , like wood-,stainless-steel-,conducitve,"magnetic"-filament does.
  
-== about 1.75mm filament ==+=== can it print 1.75mm filament ===
  
-To print 1.75mm filament, a different [[https://www.lulzbot.com/?q=products/budaschnozzle-20-ptfe-tube-175mm-filament|PTFE-Tube]] would be needed. However, Lulzbot no longer manufactures or sells them. Conceivably they are easy to make yourself from aluminum or PTFE with a lathe. Seeing as their newest [[https://www.lulzbot.com/products/lulzbot-taz-single-extruder-tool-head-v2|Hexagon Hotend]] does not even mention the option of printing anything but 3mm filament, Lulzbot seems to have completely abandoned support for anything other than 3mm filament. +**SORRY NO**
- +
-Quote from Lulzbot-Sales 2015-09-25: > I do apologize, but we no longer carry those tubes. We have tested several filaments on our printers, and prefer the 3 mm size, as it much easier to work with.+
  
 ====== Specs and Settings ====== ====== Specs and Settings ======
Line 199: Line 207:
  
 ^currently mounted Nozzle^| ^currently mounted Nozzle^|
-|Diameter|0.35mm|+|Diameter|0.5mm|
 |Max Temperature|240°C (exceed at risk of **DAMAGE**)| |Max Temperature|240°C (exceed at risk of **DAMAGE**)|
 |Type|Budaschnozzle 2.0c| |Type|Budaschnozzle 2.0c|
 +
 +===== Known Problems =====
 +
 +  * Metal Platform holding print-bed is bent at all corners
 +    * this makes leveling harder, as the bending angle is different in all four corners
 +    * this means that the Z-offset (screw below Z-Endstop on controller-side) needs to be set lower that it originally was
 +      * this means, when z-leveling, the extruder-header goes lower than it was designed for and sometimes makes hurtful noises
 +  * Folien gehört getauscht
 +    * muss aufgeheizt werden auf 60°C bevor neue Folien aufgeklebt wird, sonst bilden sich blasen
  
 ===== Current Firmware Settings ===== ===== Current Firmware Settings =====
  • /srv/dokuwiki/data/attic/3dprinting/lulzbot.1531526109.txt.gz
  • Last modified: 2025-11-09 09:24
  • (external edit)