Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
| 3dprinting:lulzbot [2018-07-13 23:48] – xro | 3dprinting:lulzbot [2025-11-09 09:25] (current) – external edit 127.0.0.1 | ||
|---|---|---|---|
| Line 20: | Line 20: | ||
| - Is the filmanet entangled? –> disentangle. | - Is the filmanet entangled? –> disentangle. | ||
| - Load correct material profile in Cura. | - Load correct material profile in Cura. | ||
| - | * If in doubt use " | + | * If in doubt use " |
| - Are you printing Nylon? | - Are you printing Nylon? | ||
| * Prep with Glue Stick. Clean/ | * Prep with Glue Stick. Clean/ | ||
| Line 43: | Line 43: | ||
| ====== Tipps and Caveats ====== | ====== Tipps and Caveats ====== | ||
| + | |||
| + | Jemand hat Ocotoprint installiert und den Lulzbot unter http:// | ||
| [[https:// | [[https:// | ||
| Line 113: | Line 115: | ||
| Current Nozzle Size is 0.5 (self-drilled). It's fast and accurate. Don't change it if in doubt. | Current Nozzle Size is 0.5 (self-drilled). It's fast and accurate. Don't change it if in doubt. | ||
| - | We also have a 0.35 Nozzle. You will only need it for very fine prints. | + | <del>We also have a 0.35 Nozzle. You will only need it for very fine prints.</ |
| **Warning** | **Warning** | ||
| Line 133: | Line 135: | ||
| ====== Materials ====== | ====== Materials ====== | ||
| - | <WRAP noprint>< | + | <WRAP center round tip 60%> ** Correct profiles for each material can be found in: ** '' |
| - | + | ||
| - | <WRAP center round tip 60%> ** Correct profiles for each material can be found in: ** '' | + | |
| **Fast Profile** | **Fast Profile** | ||
| Line 151: | Line 151: | ||
| </ | </ | ||
| - | currently | + | See [[materials|list of materials |
| - | * < | + | ==== Printing with nGen ==== |
| - | * Spool Length: ~140m | + | |
| - | * normal price | + | |
| - | * nice material strength | + | |
| - | * warps on large surface area | + | |
| - | * needs raft for less than 4cm² ground surface | + | |
| - | * [[https:// | + | |
| - | * Spool Length: 62.7m | + | |
| - | * normal price | + | |
| - | * awesome material durability and strength | + | |
| - | * needs glue and no printbed heat to stick. even so has tendency of warping on large ground surfaces and thus getting loose | + | |
| - | * recommended if cheap, small or very durable prints are needed | + | |
| - | * [[https:// | + | |
| - | * Spool Length: 56m | + | |
| - | * more expensive, double price | + | |
| - | * translucent | + | |
| - | * brittle | + | |
| - | * [[https:// | + | |
| - | * Spool Length: 56m | + | |
| - | * more expensive, double price | + | |
| - | * translucent | + | |
| - | * brittle | + | |
| - | * [[https:// | + | |
| - | * Spool Length: ~125m | + | |
| - | * normal price | + | |
| - | * [[https:// | + | |
| - | * Spool Length: ~30m | + | |
| - | * really expensive, 5 times usual price. \\ actually more than 10 times as expensive as HIPS per meter. | + | |
| - | * brittle on small features but durable like PLA and heavy on bigger pieces | + | |
| - | * sticks really well on printbed. do not use glue or can forget about getting your print off the bed | + | |
| - | * [[https:// | + | |
| - | * Spool Length: ~5m | + | |
| - | * use only for cleaning and when changing filaments | + | |
| - | * [[https:// | + | |
| - | * Spool Length 750g: ~95m | + | |
| - | * Spool Length 2200g: 270m | + | |
| - | * only slightly more expensive | + | |
| - | * least warping so good for precise prints | + | |
| - | * sticks really well to printbed | + | |
| - | * recommended for big and precise prints | + | |
| - | See the [[https:// | + | no special knowledge or care required |
| - | See also the [[https://www.lulzbot.com/ | + | ==== Printing with HIPS/PLA/ABS ==== |
| + | |||
| + | Hips, PLA and ABS like to warp to various degrees during the print due to cooling/ | ||
| ==== Printing with Nylon ==== | ==== Printing with Nylon ==== | ||
| + | |||
| + | <WRAP noprint> {{ : | ||
| Nylon does not stick to the print-bed. Not even with the heat turned on. | Nylon does not stick to the print-bed. Not even with the heat turned on. | ||
| Line 216: | Line 181: | ||
| When the print is finished, wait for the pad cools and then VERY carefully try not to damage the print surface! | When the print is finished, wait for the pad cools and then VERY carefully try not to damage the print surface! | ||
| - | === what can be printed ? === | + | ==== what materials |
| - | Everything with a filament diameter of 3mm (no less and no more) and extrusion temperature below 238°C that does not clog 0.35mm nozzles, like wood-, | + | Everything with a filament diameter of 2.85mm-3mm (no less and no more) and extrusion temperature below 238°C that does not clog the nozzle |
| - | == about 1.75mm filament == | + | === can it print 1.75mm filament |
| - | To print 1.75mm filament, a different [[https:// | + | **SORRY NO** |
| - | + | ||
| - | Quote from Lulzbot-Sales 2015-09-25: > I do apologize, but we no longer carry those tubes. We have tested several filaments on our printers, and prefer the 3 mm size, as it much easier to work with. | + | |
| ====== Specs and Settings ====== | ====== Specs and Settings ====== | ||
| Line 244: | Line 207: | ||
| ^currently mounted Nozzle^| | ^currently mounted Nozzle^| | ||
| - | |Diameter|0.35mm| | + | |Diameter|0.5mm| |
| |Max Temperature|240°C (exceed at risk of **DAMAGE**)| | |Max Temperature|240°C (exceed at risk of **DAMAGE**)| | ||
| |Type|Budaschnozzle 2.0c| | |Type|Budaschnozzle 2.0c| | ||
| + | |||
| + | ===== Known Problems ===== | ||
| + | |||
| + | * Metal Platform holding print-bed is bent at all corners | ||
| + | * this makes leveling harder, as the bending angle is different in all four corners | ||
| + | * this means that the Z-offset (screw below Z-Endstop on controller-side) needs to be set lower that it originally was | ||
| + | * this means, when z-leveling, the extruder-header goes lower than it was designed for and sometimes makes hurtful noises | ||
| + | * Folien gehört getauscht | ||
| + | * muss aufgeheizt werden auf 60°C bevor neue Folien aufgeklebt wird, sonst bilden sich blasen | ||
| ===== Current Firmware Settings ===== | ===== Current Firmware Settings ===== | ||